Prashnikaप्रश्निका
Code
About
PhysicsClass 12

Semiconductor Electronics: Materials, Devices and Simple Circuits - ISC Class 12 Physics Questions with Answers

31 past-paper questions on Semiconductor Electronics: Materials, Devices and Simple Circuits from ISC Class 12 Physics papers (2027-2019), newest first, in full. Questions 1-20 are on this page, 20 to a page. Tap "Show answer" under a question to see its answer. The syllabus covers Energy bands in solids, Intrinsic and extrinsic semiconductors and p-n junction.

31questions
8years
2027newest
20271 question
1 mark · Short answerOpen: Explain why resistance of a semiconductor material decreases when its…

Answer the following.

Explain why resistance of a semiconductor material decreases when its temperature is increased.
Show answer

Answer

Official answer key
As temperature rises, more electrons break their covalent bonds and cross the forbidden energy gap into the conduction band. The number of free charge carriers (electrons and holes) increases greatly, so the resistance decreases.
20265 questions
5 marks · Case basedOpen: A band gap is the distance between the valence band of electrons and the…

Answer the following.

A band gap is the distance between the valence band of electrons and the conduction band. Essentially, the band gap represents the minimum energy that is required to excite an electron up to a state in the conduction band where it can participate in conduction. The lower energy level is the valence band, and thus if a gap exists between this level and the higher energy conduction band, energy must be input for electrons to become free. An LED is made of a p-type semiconductor material (which has a higher concentration of "holes" or positive charge carriers) and an n-type semiconductor material (which has a higher concentration of electrons or negative charge carriers). This recombination process releases energy in the form of light and heat. The specific wavelength (and therefore the colour) of the emitted light depends on the energy band gap of the semiconductor material used. I-V characteristic of LED bulb is given below.
Figure for this question
(i)[2]
Identify the wavelength that has: (a) The maximum energy gap (b) The minimum energy gap
(ii)[3]
$E$ is the energy of the incident photon and $E_g$ is energy gap, which is produced across the depletion layer. What will happen in the following cases: (a) $E > E_g$ (b) $E = E_g$ (c) $E < E_g$
Show answer

Answer (i)

Official answer key
(a) The maximum energy gap: wavelength 3 (b) The minimum energy gap: wavelength 1

Answer (ii)

Official answer key
(a) $E > E_g$: a photon with energy is emitted. (b) $E = E_g$: a photon with no (zero excess) energy is emitted. (c) $E < E_g$: no photon is emitted.
1 mark · Short answerOpen: What is the direction of flow of electrons in a solar cell?

Answer the following.

What is the direction of flow of electrons in a solar cell?
Show answer

Answer

Official answer key
Electrons move towards the n-type material (and holes towards the p-type), so a current flows when an external circuit is connected.
5 marks · DrawingOpen: Draw a labelled circuit diagram of a semiconductor diode when it is forward…

Answer the following.

(i)[2]
Draw a labelled circuit diagram of a semiconductor diode when it is forward biased.

Draw: a semiconductor diode when it is forward biased

(ii)[1]
What is meant by 'doping'?
(iii)[1]
Draw a labelled energy band diagram of a semiconductor.

Draw: an energy band diagram of a semiconductor

(iv)[1]
Which diode is used as a voltage stabiliser?
Show answer

Answer (i)

Worked out by the server: every current and potential difference

PartCurrentp.d.
E10.03 A3 V
R10.03 A3 V
A10.03 A0 V
D10.03 A0 V
A p-n junction diode connected in forward bias: the p-side (anode) is connected to the positive terminal of the battery and the n-side (cathode) to the negative terminal, through a resistor R and a milliammeter, so that a current flows from p to n.

Answer (ii)

Doping is the process of deliberately adding a small amount of a suitable impurity (trivalent or pentavalent atoms) to a pure (intrinsic) semiconductor to increase its conductivity.

Answer (iii)

An energy band diagram of a semiconductor shows a filled valence band at the bottom, an almost empty conduction band at the top, and a narrow forbidden energy gap $E_g$ between them (about 1 eV; e.g. 1.1 eV for Si).

Answer (iv)

Zener diode.
5 marks · Short answerOpen: What is the effect of increasing the temperature on conductivity of an…

Answer the following.

(v)[1]
What is the effect of increasing the temperature on conductivity of an intrinsic semiconductor?
(vi)[1]
Draw a labelled energy band diagram of a metal.

Draw: an energy band diagram of a metal

(vii)[1]
What is meant by reverse biasing of a semiconductor diode?
(viii)[2]
State any one advantage of full wave rectification over a half wave rectification.
Show answer

Answer (v)

The conductivity of an intrinsic semiconductor increases with temperature, because more covalent bonds break and more electron-hole pairs are generated.

Answer (vi)

In a metal the valence band and the conduction band overlap (or the conduction band is partly filled), so there is no forbidden gap ($E_g = 0$) and plenty of free electrons are available for conduction.

Answer (vii)

In reverse biasing the p-side of the diode is connected to the negative terminal and the n-side to the positive terminal of the battery. This widens the depletion region and increases the barrier potential, so almost no current flows (only a tiny leakage current due to minority carriers).

Answer (viii)

Any one: the full-wave rectifier has higher rectification efficiency (about 81.2% against 40.6%), the output has less ripple (it is smoother/more continuous, and the ripple frequency is twice the input frequency, so it is easier to filter), and both half cycles of the input are used.
20257 questions
5 marks · Case basedOpen: Discovery of semiconducting devices has revolutionised the field of…

Answer the following.

Discovery of semiconducting devices has revolutionised the field of electronics. Earlier, a computer known as first generation computer, was as big as a room! The radio sets used to be so bulky that they could not be taken on a picnic. Semiconducting devices, being light and compact, have changed all that. Now, computers have become so small in size that they are called laptops and palm tops. Semiconducting devices, that are widely used in electronic gadgets like a television, a radio, an amplifier etc, are diodes, transistors, FETs, ICs, logic gates etc. Diodes are of different types like light emitting diodes, photodiodes, Zener diodes etc. They perform various functions like converting an ac voltage to dc voltage, emit light etc.
(i)[1]
State any one advantage of a semiconducting device over an old electronic device.
(ii)[1]
What energy transformation takes place in an LED?
(iii)[1]
What is the function of a rectifier?
(iv)[2]
Figure 12 below shows a rectifier. In case of the rectifier shown above, draw the graphs to show the waveform of: (a) input voltage. (b) output voltage.

Draw: waveform graphs for input voltage and output voltage of a rectifier

Must show: input sinusoidal AC waveform, rectified waveform across load resistor R

Figure for part (iv)
Show answer

Answer (i)

A semiconducting device is small and light (compact), consumes much less power, needs no warm-up time and lasts longer than an old vacuum tube device.

Answer (ii)

In an LED, electrical energy is converted into light energy.

Answer (iii)

A rectifier converts alternating current (voltage) into direct current (voltage).

Answer (iv)

Worked out by the server: A half-wave rectifier: the diode conducts only in the positive half-cycles, so the output is the positive half-cycles with gaps between them, at the input's frequency.

(a) Input voltage: a continuous sine wave of the a.c. supply, alternating positive and negative in each period $T$. (b) Output voltage across $R$ (half-wave rectifier): only the positive half-cycles appear, as pulses with the same period $T$; during each negative half-cycle the diode is reverse biased and the output is zero.
1 mark · MCQOpen: N-type semiconductor is that which has:

Choose the correct option.

N-type semiconductor is that which has:
  • (a)majority of holes as charge carriers.
  • (b)majority of free electrons as charge carriers.
  • (c)trivalent element added as an impurity.
  • (d)an equal number of holes and free electrons.
Show answer

Answer

Correct option: (b)

Answer: (b) majority of free electrons as charge carriers. An n-type semiconductor is doped with a pentavalent impurity, so electrons are the majority carriers.
1 mark · MCQOpen: If temperature of a block of a semiconducting material is increased, its…

Choose the correct option.

If temperature of a block of a semiconducting material is increased, its resistance:
  • (a)decreases.
  • (b)increases.
  • (c)remains constant.
  • (d)first increases and then decreases.
Show answer

Answer

Correct option: (a)

Answer: (a) decreases. More charge carriers are generated at a higher temperature, so the resistance of a semiconductor falls.
5 marks · Case basedOpen: When a television set (scientifically known as a television receiver) is…

Answer the following.

When a television set (scientifically known as a television receiver) is opened, many components like semiconductor diodes, transistors, capacitors, resistors etc. can be observed on its motherboard. There are different types of diodes like photo diode, Zener diode, LED etc. found in the T.V. set. With the help of these components, a television receives audio as well as video signals.
(i)[1.5]
A semiconductor diode has two types of semiconducting materials: ‘P’ type and ‘N’ type. What is the difference between them?
(ii)[1.5]
Draw a labelled diagram of a full wave rectifier. Show graphically how its output voltage varies with time.

Draw: circuit diagram of a full wave rectifier with centre-tapped transformer, two diodes, and load resistor, along with input and output voltage waveforms

Must show: centre-tapped transformer, two p-n junction diodes D1 and D2, load resistor R_L, input AC waveform, output rectified DC waveform

(iii)[2]
What type of diode can be used as a voltage regulator?
Show answer

Answer (i)

BasisP-typeN-type
DopantTrivalent impurity (e.g. boron, aluminium)Pentavalent impurity (e.g. phosphorus, arsenic)
Majority carriersHolesElectrons
Minority carriersElectronsHoles

Answer (ii)

Worked out by the server: A full-wave rectifier with a centre-tapped transformer: D1 conducts in one half-cycle and D2 in the other, so the current through the load is always the same way and the output frequency is twice the input's.

Centre-tapped full wave rectifier: the secondary of the transformer has a centre tap, connected to one end of the load $R_L$; the two ends of the secondary connect to the anodes (p-sides) of diodes $D_1$ and $D_2$, whose cathodes (n-sides) are joined and connected to the other end of $R_L$. During one half cycle of the input $D_1$ conducts and during the other half cycle $D_2$ conducts, so the current through $R_L$ is always in the same direction. Input: a sine wave of period $T$. Output across $R_L$: only positive humps (pulsating d.c.), two humps in every period $T$, so the output frequency is twice the input frequency.

Answer (iii)

Zener diode (operated in reverse breakdown).
20241 question
1 mark · MCQOpen: The majority charge carriers in a P-type semiconductor are

Choose the correct option.

The majority charge carriers in a P-type semiconductor are
  • (a)electrons.
  • (b)holes.
  • (c)protons.
  • (d)ions.
Show answer

Answer

Correct option: (b)

Answer: (b) holes. A p-type semiconductor is doped with a trivalent impurity, which creates holes; holes are the majority charge carriers and electrons the minority carriers.
20236 questions
1 mark · Short answerOpen: In semiconductors, what is meant by “doping”?

Answer the following.

In semiconductors, what is meant by “doping”?
Show answer

Answer

Doping is the deliberate addition of a small amount of a suitable impurity (trivalent or pentavalent) to a pure semiconductor to increase its conductivity.
1 mark · MCQOpen: ‘n’ type semiconductor is that which has

Choose the correct option.

‘n’ type semiconductor is that which has
  • (a)holes as majority carriers.
  • (b)free electrons as majority carriers.
  • (c)holes and free electrons equal in number.
  • (d)trivalent element as an impurity.
Show answer

Answer

Correct option: (b)

Answer: (b) free electrons as majority carriers. An n-type semiconductor is doped with a pentavalent impurity, which donates free electrons.
1 mark · MCQOpen: With an increase in the temperature, electrical conductivity of a semiconductor:

Choose the correct option.

With an increase in the temperature, electrical conductivity of a semiconductor:
  • (a)decreases.
  • (b)increases.
  • (c)does not change.
  • (d)first increases and then decreases.
Show answer

Answer

Correct option: (b)

Answer: (b) increases. On heating, more electrons move from the valence band to the conduction band, so the number of charge carriers increases and conductivity rises.
1 mark · Short answerOpen: What is meant by “Forbidden band” of energy levels?

Answer the following.

What is meant by “Forbidden band” of energy levels?
Show answer

Answer

The forbidden band (energy gap, $E_g$) is the range of energies between the top of the valence band and the bottom of the conduction band in which no electron can have an energy.

About Semiconductor Electronics: Materials, Devices and Simple Circuits

Semiconductor Electronics: Materials, Devices and Simple Circuits is a chapter of the Electronic Devices unit of the ISC Class 12 Physics syllabus. The syllabus gives 7 of the 70 theory marks to Electronic Devices.

The syllabus lists these topics: Energy bands in solids, Intrinsic and extrinsic semiconductors and p-n junction.

Prashnika has 31 past-paper questions on Semiconductor Electronics: Materials, Devices and Simple Circuits, from papers of 2019-2027, asked in 8 different years. By kind: Short answer (16), MCQ (5), Case based (3) and One word (3). They carry between 1 and 5 marks, and most are worth 1 mark.

To practise, use the paper generator, which can build a practice paper from this chapter.

Common questions

What topics are in Semiconductor Electronics: Materials, Devices and Simple Circuits in ISC Class 12 Physics?

The syllabus lists Energy bands in solids, Intrinsic and extrinsic semiconductors and p-n junction.

How many questions on Semiconductor Electronics: Materials, Devices and Simple Circuits are in ISC Class 12 Physics past papers?

Prashnika has 31 questions on Semiconductor Electronics: Materials, Devices and Simple Circuits, from papers of 2019-2027 (board, specimen, improvement and practice papers together).

What kinds of questions are asked on Semiconductor Electronics: Materials, Devices and Simple Circuits?

By kind: Short answer (16), MCQ (5), Case based (3) and One word (3).

Questions on other pages on Semiconductor Electronics: Materials, Devices and Simple Circuits