Prashnikaप्रश्निका
Code
About
PhysicsClass 12

Semiconductor diode - ISC Class 12 Physics Questions with Answers

36 past-paper questions on Semiconductor diode from ISC Class 12 Physics papers (2027-2018), newest first, in full. Questions 1-20 are on this page, 20 to a page. Tap "Show answer" under a question to see its answer. The syllabus covers I-V characteristics in forward and reverse bias, Diode as a rectifier, Special types of junction diodes and Zener diode as voltage regulator.

36questions
8years
2027newest
20276 questions
1 mark · Short answerOpen: What is a solar cell?

Answer the following.

What is a solar cell?
Show answer

Answer

Official answer key
A solar cell (photovoltaic cell) is a semiconductor p-n junction diode that directly converts solar (light) energy into electrical energy.
1 mark · Short answerOpen: Explain its working in brief.

Answer the following.

Explain its working in brief.
Show answer

Answer

Official answer key
Photons of energy greater than the band gap fall on the junction and break covalent bonds near it, producing electron-hole pairs. The junction field sweeps electrons to the n-side and holes to the p-side, so charges build up and a potential difference (emf) appears across the cell. When an external load is connected, a direct current flows through it.
1 mark · Short answerOpen: Extrinsic semiconductors are neither good nor bad conductors of electricity…

Answer the following.

Extrinsic semiconductors are neither good nor bad conductors of electricity. Why are they still considered useful?
Show answer

Answer

Because their conductivity can be controlled by the amount and kind of doping (n-type or p-type), so p-type and n-type material can be joined to make p-n junction diodes, transistors and integrated circuits.
1 mark · MCQOpen: Identify the phenomena that occur when a P-N junction diode is forward biased…

Choose the correct option.

Identify the phenomena that occur when a P-N junction diode is forward biased: (P) The width of the depletion layer decreases. (Q) The height of the potential barrier is lowered. (R) The effective resistance of the diode increases significantly. (S) The reverse current flows mainly due to the diffusion of majority charge carriers.
  • aBoth (P) and (Q)
  • bBoth (R) and (S)
  • cBoth (P) and (S)
  • dBoth (Q) and (R)
Show answer

Answer

Official answer key

Correct option: a

Answer: (a) Both (P) and (Q) On forward bias the depletion layer narrows and the potential barrier is lowered, while the effective resistance falls (R is false) and (S) describes reverse bias, which is due to minority carriers (S is false).
20265 questions
1 mark · MCQOpen: Which one of the following statements is true for the width of the depletion…

Choose the correct option.

Which one of the following statements is true for the width of the depletion region of a semi-conductor diode?
  • (a)Increases during forward bias and remains constant during reverse bias
  • (b)Increases during forward bias and decreases during reverse bias
  • (c)Decreases during forward bias and increases during reverse bias
  • (d)Remains constant during forward bias and increases during reverse bias
Show answer

Answer

Correct option: (c)

Answer: (c) Decreases during forward bias and increases during reverse bias Forward bias pushes majority carriers towards the junction, narrowing the depletion region; reverse bias pulls them away and widens it.
1 mark · DrawingOpen: Draw the symbol of a Zener diode.

Draw the following.

Draw the symbol of a Zener diode.

Draw: Symbol of a Zener diode

Show answer

Answer

The symbol of a Zener diode consists of a triangle representing the anode pointing towards a bar representing the cathode. The cathode bar has bent ends at both edges (resembling the letter 'Z') to distinguish it from an ordinary p-n junction diode.
Diagram for this answer
5 marks · Case basedOpen: Annie, a student of Physics, began her experiment by fabricating a p-n junction…

Answer the following.

Annie, a student of Physics, began her experiment by fabricating a p-n junction diode from an extrinsic semiconductor crystal, leading to the formation of a depletion region and a potential barrier at the interface. She then measured resistance of the diode in the linear region of the V-I characteristic curve. She also studied its characteristics during forward bias and reverse bias. Finally, she designed a circuit to convert ac voltage to dc voltage.
Read the scenario given below and answer the questions that follow.
(i)[1]
Which instrument was used by Annie to measure current flowing through the diode during its reverse bias?
(ii)[1]
How did Annie obtain an extrinsic semiconductor from an intrinsic semiconductor?
(iii)[1]
What is meant by potential barrier?
(iv)[2]
Draw a labelled circuit diagram of a half wave rectifier.

Draw: labelled circuit diagram of a half wave rectifier

Must show: ac supply or transformer, p-n junction diode, load resistor RL, dc output across RL

Show answer

Answer (i)

A microammeter ($\mu\text{A}$) was used to measure the very small reverse current flowing through the diode.

Answer (ii)

Annie obtained an extrinsic semiconductor by doping the pure (intrinsic) semiconductor—that is, by adding a controlled, minute quantity of a suitable impurity (such as trivalent or pentavalent atoms) into the intrinsic semiconductor lattice.

Answer (iii)

Potential barrier is the potential difference established across the depletion layer of a p-n junction due to the accumulation of immobile ions, which opposes and prevents further diffusion of majority charge carriers across the junction.

Answer (iv)

A labelled circuit diagram of a half-wave rectifier shows an ac mains source connected to the primary of a step-down transformer. The secondary coil is connected in series with a single p-n junction diode (anode connected to the upper terminal of the secondary) and a load resistor $R_L$ connected to the lower terminal. The pulsating dc output voltage is taken across the load resistor $R_L$.
Diagram for this answer
1 mark · MCQOpen: When a p-n junction diode is forward-biased

Choose the correct option.

When a p-n junction diode is forward-biased
  • (a)it acts as an insulator and no current flows through it.
  • (b)it offers a low resistance and a large current flows through it.
  • (c)it offers a high resistance and a small current flows through it.
  • (d)the width of depletion region increases.
Show answer

Answer

Correct option: (b)

Answer: (b) it offers a low resistance and a large current flows through it. In forward bias, the applied voltage opposes the barrier potential and reduces the width of the depletion region, so the diode offers low resistance and allows a large current to flow.
1 mark · MCQOpen: In which of the following figures, is the p-n diode forward biased?

Choose the correct option.

In which of the following figures, is the p-n diode forward biased?
  • (a)Only (P), (Q) and (S)
  • (b)Only (R)
  • (c)Only (P) and (R)
  • (d)Only (Q) and (S)
Figure for this question
Show answer

Answer

Official answer key

Correct option: (b)

Answer: (b) Only (R) A p-n diode is forward biased when the p-side is at a higher potential than the n-side; this is so only in figure (R), as in the answer key.
20259 questions
1 mark · Short answerOpen: A solar cell is a junction diode. A very thin layer of p-type semiconductor is…

Answer the following.

A solar cell is a junction diode. A very thin layer of p-type semiconductor is grown on a relatively thicker n-type semiconductor, having a few finer electrodes on the top of the p-type semiconductor layer. These electrodes do not obstruct light from reaching the thin p-type layer. Just below the p-type layer, there is a p-n junction. We also provide a current-collecting electrode at the bottom of the n-type layer. Similarly, the holes in the depletion can quickly come to the p-type side of the junction. Once the newly created free electrons come to the n-type side, they cannot further cross the junction because of the barrier potential of the junction. Similarly, the newly created holes once they come to the p-type side cannot further cross the junction because of the same barrier potential of the junction. As the concentration of electrons becomes higher on one side, the p-n junction will behave like a small battery cell. A voltage is set up which is known as photovoltage. If we connect a small load across the junction, there will be a tiny current flowing through it. The I-V characteristic of solar cells is given in the figure. What does $V_0$ represent in the characteristic curve?
Figure 93
Figure 93
Show answer

Answer

Official answer key
Maximum potential when the solar cell is in an open circuit.
1 mark · Short answerOpen: A solar cell is a junction diode. A very thin layer of p-type semiconductor is…

Answer the following.

A solar cell is a junction diode. A very thin layer of p-type semiconductor is grown on a relatively thicker n-type semiconductor, having a few finer electrodes on the top of the p-type semiconductor layer. These electrodes do not obstruct light from reaching the thin p-type layer. Just below the p-type layer, there is a p-n junction. We also provide a current-collecting electrode at the bottom of the n-type layer. Similarly, the holes in the depletion can quickly come to the p-type side of the junction. Once the newly created free electrons come to the n-type side, they cannot further cross the junction because of the barrier potential of the junction. Similarly, the newly created holes once they come to the p-type side cannot further cross the junction because of the same barrier potential of the junction. As the concentration of electrons becomes higher on one side, the p-n junction will behave like a small battery cell. A voltage is set up which is known as photovoltage. If we connect a small load across the junction, there will be a tiny current flowing through it. The I-V characteristic of solar cells is given in the figure. Is the principle of a solar cell the same as that of a photodiode?
Figure 93
Figure 93
Show answer

Answer

Official answer key
Yes.
1 mark · Short answerOpen: A solar cell is a junction diode. A very thin layer of p-type semiconductor is…

Answer the following.

A solar cell is a junction diode. A very thin layer of p-type semiconductor is grown on a relatively thicker n-type semiconductor, having a few finer electrodes on the top of the p-type semiconductor layer. These electrodes do not obstruct light from reaching the thin p-type layer. Just below the p-type layer, there is a p-n junction. We also provide a current-collecting electrode at the bottom of the n-type layer. Similarly, the holes in the depletion can quickly come to the p-type side of the junction. Once the newly created free electrons come to the n-type side, they cannot further cross the junction because of the barrier potential of the junction. Similarly, the newly created holes once they come to the p-type side cannot further cross the junction because of the same barrier potential of the junction. As the concentration of electrons becomes higher on one side, the p-n junction will behave like a small battery cell. A voltage is set up which is known as photovoltage. If we connect a small load across the junction, there will be a tiny current flowing through it. The I-V characteristic of solar cells is given in the figure. Why do holes in the depletion region quickly come to the p-side?
Figure 93
Figure 93
Show answer

Answer

Official answer key
Due to potential barriers.
1 mark · Short answerOpen: A solar cell is a junction diode. A very thin layer of p-type semiconductor is…

Answer the following.

A solar cell is a junction diode. A very thin layer of p-type semiconductor is grown on a relatively thicker n-type semiconductor, having a few finer electrodes on the top of the p-type semiconductor layer. These electrodes do not obstruct light from reaching the thin p-type layer. Just below the p-type layer, there is a p-n junction. We also provide a current-collecting electrode at the bottom of the n-type layer. Similarly, the holes in the depletion can quickly come to the p-type side of the junction. Once the newly created free electrons come to the n-type side, they cannot further cross the junction because of the barrier potential of the junction. Similarly, the newly created holes once they come to the p-type side cannot further cross the junction because of the same barrier potential of the junction. As the concentration of electrons becomes higher on one side, the p-n junction will behave like a small battery cell. A voltage is set up which is known as photovoltage. If we connect a small load across the junction, there will be a tiny current flowing through it. The I-V characteristic of solar cells is given in the figure. Is $I_{max}$ independent of the intensity of incident radiation?
Figure 93
Figure 93
Show answer

Answer

Official answer key
No.
5 marks · Case basedOpen: Sanya performed an experiment of obtaining characteristic curves of a junction…

Answer the following.

Sanya performed an experiment of obtaining characteristic curves of a junction diode. When she forward biased it, she found that beyond forward voltage $V = V_k$, the conductivity is very high. When she reverse biased the diode she found that a very small current (of about a few microamperes) flows in the diode. It remained constant even though she varied the voltage.
(i)[1]
In Figure 11, which one of the diodes is forward biased?
Figure for part (i)
(ii)[1]
What is meant by a saturation current?
(iii)[1.5]
When applied voltage during forward bias is small, why does no current flow in the diode?
(iv)[1.5]
The circuit shown in the Figure 12 below contains two diodes, each with a forward resistance of $50\ \Omega$ and with infinite resistance during reverse bias. If the battery voltage is $6\text{ V}$, then calculate the current through the $100\ \Omega$ resistance.
Figure for part (iv)
Show answer

Answer (i)

Official answer key
$D_2$ is forward biased.

Answer (ii)

Official answer key
It is that current which remains constant even on increasing the p.d.

Answer (iii)

Official answer key
Due to the potential barrier (barrier p.d.).

Answer (iv)

Official answer key
Ignoring $D_2$ as it is reverse biased and offers infinite resistance, by Ohm's law, $I = \frac{E}{R + R'} = \frac{6}{50 + 150 + 100} = \frac{6}{300} = 0.02\ \text{A}$

Final answer: 0.02 A

1 mark · MCQOpen: A solar cell is a junction diode. A very thin layer of p-type semiconductor is…

Answer the following.

A solar cell is a junction diode. A very thin layer of p-type semiconductor is grown on a relatively thicker n-type semiconductor, having a few finer electrodes on the top of the p-type semiconductor layer. These electrodes do not obstruct light from reaching the thin p-type layer. Just below the p-type layer, there is a p-n junction. We also provide a current-collecting electrode at the bottom of the n-type layer. Similarly, the holes in the depletion can quickly come to the p-type side of the junction. Once the newly created free electrons come to the n-type side, they cannot further cross the junction because of the barrier potential of the junction. Similarly, the newly created holes once they come to the p-type side cannot further cross the junction because of the same barrier potential of the junction. As the concentration of electrons becomes higher on one side, the p-n junction will behave like a small battery cell. A voltage is set up which is known as photovoltage. If we connect a small load across the junction, there will be a tiny current flowing through it. The I-V characteristic of solar cells is given in the figure. What is the suitable band gap of the semiconductors used as solar cell materials?
  • (a)0 to 0.5 eV
  • (b)0.5 to 1 eV
  • (c)1.1 to 2 eV
  • (d)0 to 0.8 eV
Figure 93
Figure 93
Show answer

Answer

Official answer key

Correct option: (c)

Option c – 1.1 to 2 eV
1 mark · MCQOpen: What will be the output for the given circuit?

Choose the correct option.

What will be the output for the given circuit?
  • (a)Zero
  • (b)Positive half-cycles only
  • (c)Negative half-cycles only
  • (d)Full AC waveform
Show answer

Answer

Official answer key

Correct option: (b)

(b) During the first half diode is in reverse biasing so it does not conduct, and we get the same voltage in output. But in the second half, it is in forward bias, so it conducts, hence the circuit is shortened, and we do not get any voltage in output.
1 mark · DrawingOpen: A light-emitting diode (LED) is connected in forward biasing. If its potential…

Draw the following.

A light-emitting diode (LED) is connected in forward biasing. If its potential barrier is given by ‘$V_0$’ when no biasing is there, as shown in the diagram, then draw the diagram showing the new position of potential barrier.

Draw: diagram of potential barrier in forward biased LED

Show answer

Answer

Official answer key
On forward biasing, the potential barrier decreases. The new potential barrier is drawn lower than the original barrier $V_0$, with the barrier height reduced as marked by the arrows.
Potential barrier diagram with the original barrier V0 and a new, lower potential barrier labelled 'New potential barrier'.

About Semiconductor diode

Semiconductor diode is a chapter of the Electronic Devices unit of the ISC Class 12 Physics syllabus. The syllabus gives 7 of the 70 theory marks to Electronic Devices.

The syllabus lists these topics: I-V characteristics in forward and reverse bias, Diode as a rectifier, Special types of junction diodes and Zener diode as voltage regulator.

Prashnika has 36 past-paper questions on Semiconductor diode, from papers of 2018-2027, asked in 8 different years. By kind: Short answer (19), MCQ (7), Drawing (6) and Case based (2). They carry between 1 and 5 marks, and most are worth 1 mark.

To practise, use the paper generator, which can build a practice paper from this chapter.

Common questions

What topics are in Semiconductor diode in ISC Class 12 Physics?

The syllabus lists I-V characteristics in forward and reverse bias, Diode as a rectifier, Special types of junction diodes and Zener diode as voltage regulator.

How many questions on Semiconductor diode are in ISC Class 12 Physics past papers?

Prashnika has 36 questions on Semiconductor diode, from papers of 2018-2027 (board, specimen, improvement and practice papers together).

What kinds of questions are asked on Semiconductor diode?

By kind: Short answer (19), MCQ (7), Drawing (6) and Case based (2).

Questions on other pages on Semiconductor diode